Compartment lighting system a led lamps group pre-wired

ADVANTAGES LIGHTED CRAM

SAFETY, LOW VOLTAGE OPERATON

Using CRAM's led lamps, you work (except in the pit on taking 230Vac 50Hz) always with low voltage 24VDC, low power (2.8 W lamp), no point ""hot" because with the low power involved, even the lamps are "cold."

EASY ASSEMBLY

With our system, which separates from the wall bracket lamp with a touch, and provides all the connectors "fast" polarized, you can run the wiring of lighting in an elementary way.
For example, the work of fixing the wall bracket, the application and the connection of the lamp can be performed by two different people.

HIGH EFFICIENCY LIGHT SOURCE

Using leds with approximately 3W of power you have a luminous intensity of 75 cd (candelas). Furthermore, leds have a light source called "low environmental impact."
Keep in mind that light bulbs (the most common on the market) are discarded. For example, the 100W lamps are no longer in production.

VERY LONG LIFE CYCLE

Compared to traditional incandescent lighting, a lamp life of led technology is about 5 times higher. Consequently, the actual maintenance is reduced..
Led lamp: about 40,000 hours life.
Incandescent lamp: approx 8000 hours life.

SYSTEM PRE-WIRED

Sistema illuminazione vano con lampade a led con gruppo pre-cablato

SYSTEM PRE-WIRED

LED LAMP

Led lamp, 24VDC. Supplied with cable connection sequence (5 meters), the other lamps connector "fast". Fixing kit with plastic anchors and screws.

Dati tecnici generali
Total size lamp + support 107 x 165 h45 (mm) lamp
Housing and Support Galvanized steel
Connectors "fast" - direct connection with retaining spring
Transparent protection Clear polycarbonate, UV resistant and shock
Limits of Power 22Vcc ... 28Vcc
Consumption 120 mA
Typical power 2,8 W
Typical Luminous Intensity 75 cd

CABLE

Group pre-wired conpoused by:

  • Cable terminal 7 wires x 1,5mm including yellow/green ground, standard length 8m
  • Group 230Vac outlet + Switch
  • Cable connecting the first lamp, standard length 3m.
PRODUCT VARIANTS PRODUCT CODES cavo
Socket type italian / german (as shown) PRE-IT
Socket type french PRE-FR
Socket type english PRE-UK
Cable lenght changes on request.

SCHEME

scheme led lamp

INSTRUCTIONS

Instructions for assembly the led lamp.

Use a screwdriver to separate the lamp from the wall support. montaggio 1
Once separated, the pieces are presented in this way. Support on the left and lamp on the right montaggio 2
With the use of a pencil, mark the position of mounting holes on the wall. montaggio 3
Once fixed on the stand, attach the lamp. Pushing on the side as shown, and observing the anchor points. montaggio 5
DO NOT PUSH THE LAMP THROUGH THE TRANSPARENT PLEXIGLASS montaggio 6

Attention, engage the lamp on the support, taking the electrical connectors on the correct side of the lamp

The electrical connection is made through the appropriate connectors for "fast" on the side of the lamp. The wiring connection is included in the kit. The connector is polarized with the wiring.

GENERAL TECHNICAL DATA
Total dimensions of the support + lamp 107 x 165 h 45 (mm)
Limits of power 22Vcc … 28Vcc
Consumption 120 mA
Typical brightness intensity 75cd

OPTIONAL FEEDER

DIMENSIONS - VERSION AL25 OPTIONAL FEEDER
lenght 78 mm (excluding terminals)
lenght 92 mm (with terminals)
width    51 mm
height    28 mm
DIMENSIONS - VERSION AL75
lenght 129 mm (excluding terminals)
lenght 144 mm (with terminals)
width 98mm
height 38mm
PRODUCT CODES
AL25 (up to 8 lamps)
AL75 (9 to 22 lamps)